Headlight and turn signal switch

Xenon headlights (if so equipped)

HIGH VOLTAGE

- When xenon headlights are on, they produce a high voltage. To prevent an HIGH VOLTAGE

- When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.

- Xenon headlights provide considerably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your vehicle to a NISSAN dealer and have the headlights adjusted correctly.

When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.

- The life of xenon headlights will be shortened by frequent on-off operation.

It is generally desirable not to turn off the headlights for short intervals (for example, when the vehicle stops at a traffic signal).

- If the xenon headlight bulb is close to burning out, the brightness will drastically decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.

Autolight system (if so equipped)
Autolight system (if so equipped)

The autolight system allows the headlights to be set so they turn on and off automatically.

To set the autolight system:
1. Make sure the headlight switch is in the AUTO position.

2. Turn the ignition switch to the ON position.

3. The autolight system automatically turns the headlights on and off.

To turn the autolight system off, turn the switch to the OFF, position. or The autolight system can turn on the headlights automatically when it is dark position.

The autolight system can turn on the headlights automatically when it is dark and turn off the headlights when it is light.

If the ignition switch is turned to the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for 5 minutes.

Automatic headlights off delay:

You can keep the headlights on for up to 180 seconds after you turn the ignition switch to OFF and open any door then close all the doors.

Be sure not to put anything on top of the photo sensor 1 located on

Be sure not to put anything on top of the photo sensor 1 located on the top of the instrument panel. The photo sensor controls the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate.

Type A
Type A

Type B
Type B

Headlight switch

Lighting

1 Turn the switch to the position: position:
The front park, side marker, tail, license plate and instrument lights will come on.

2 Turn the switch to the position: position:
Headlights will come on and all the other lights remain on.

Headlight beam select

Headlight beam select
Headlight beam select

1 To select the low beam, put the lever in the neutral position as shown.

2 To select the high beam, push the lever forward while the switch is in the the low beam. position. Pull it back to select the low beam.

3 Pulling the lever toward you will flash the headlight high beam even when the headlight switch is in the OFF position.

Battery saver system

- When the headlight switch is in the position while the ignition switch or is in the ON position, the lights will automatically turn off 5 minutes after the position while the ignition switch is in the ON position, the lights will automatically turn off 5 minutes after the ignition switch has been turned to the OFF position.

- When the headlight switch remains in the position after the lights automatically or turn off, the lights will turn on when the ignition switch is turned to the ON position. position after the lights automatically turn off, the lights will turn on when the ignition switch is turned to the ON position.

- When you turn on the headlight switch again after the lights automatically

- When you turn on the headlight switch again after the lights automatically turn off, the lights will not turn off automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, otherwise the battery will be discharged.

- Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.

Headlight aiming control (if so equipped)

Headlight aiming control (if so equipped)
Headlight aiming control (if so equipped)

Depending on the number of occupants in the vehicle and the load it is carrying, the headlight axis may be higher than desired. If the vehicle is traveling on a hilly road, the headlights may directly hit the rearview mirror of the vehicle ahead or the windshield of the oncoming vehicle. The light axis can be lowered with the operation of the switch.

The larger the number designated on the switch, the lower the axis.

When traveling with no heavy load or on a flat road, select position 0.

Xenon headlights are extremely bright compared to conventional headlights.

Xenon headlights are extremely bright compared to conventional headlights. If the xenon headlights hit the rearview mirror of the vehicle ahead or the windshield of oncoming vehicle, the driver of these vehicles may have difficulty driving because of the brightness.

Use the headlight aiming control switch to lower the light axis. See “Xenon headlights” earlier in this section for additional information.

Daytime running light system (Canada only)

The daytime running lights automatically illuminate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position or in the position. Turn the headlight switch to the position. Turn the headlight switch to the driving at night. position for full illumination when driving at night.

If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is turned to the OFF position.

When the daytime running light system is active, tail lights on your vehicle

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

Turn signal switch

1 Turn signal

1 Turn signal

Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically.

2 Lane change signal

To indicate a lane change, move the lever up or down to the point where lights begin flashing.

Fog light switch (if so equipped)

To turn the fog lights on, turn the headlight switch to the

To turn the fog lights on, turn the headlight switch to the position. To turn them off, turn the position, then turn the switch to the switch to the OFF position. position. To turn them off, turn the switch to the OFF position.

The headlights must be on for the fog lights to operate.

When the headlight high-beam is selected, the fog lights turn off.

    See also:

    Brake system
    Braking precautions The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. You may feel a small click and hear a sound when t ...

    Anti-lock Braking System (ABS)
    WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle ...

    Cruise control operations
    The cruise control allows driving at a speed between 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the ON·OFF switch on. Th ...